Two-component water-based epoxy resin. It stands out for its very high adhesion even on surfaces with a certain humidity (below 8%). Acts as a vapor barrier to block rising moisture. It can also be used as a water-based epoxy varnish on microcements or mortars. It has a high chemical and mechanical resistance. In addition to scratch resistance and waterproofing. Does not contain organic solvents. Volume: 5L + 2L
Low viscosity water based epoxy resin. It acts as a consolidator and surface hardener for weak substrates such as poor cement mortars, lime mortars, old concrete, etc. It can be applied in: concrete, cement mortars, lime mortars, gypsum, anhydrite and brick. It stands out for its high power of penetration and consolidation of dusty surfaces, in addition to the homogenization of porosity. Volume: 5L + 1L Volume: 5L + 2L
Two-component epoxy resin with a high solids content (80%). High chemical resistance and waterproofing. It acts as a vapor barrier to block rising moisture and inhibits damp spots that occur in tile joints. It can also be used as a colorless epoxy varnish on microcements or mortars. It has high chemical and mechanical resistance and scratch resistance. Easy application with a roller. Volume: 5L + 2L Volume: 5L + 1L Volume: 5L + 2L
It is a water-based resin that acts as an adhesion promoter between a non-porous surface (tile, marble, metal or terrazzo) and microcement. It stands out for its high adhesion and for the permanent maintenance of adhesion (residual adhesion), which allows a long action time in the application of the subsequent layer of microcement. It has great elasticity that makes it excellently resistant to different climatic conditions. Volume: 1l, 5L, 25L Volume: 5L + 2L
It is a decorative self-leveling with the same properties as Decolevel Floor. The difference between one and the other is that Decolevel Fast has a harder finish and is only gray in color. In addition, it has a faster drying time, between 4 and 5 hours. Classified according to UNE-EN 13813 as CT-C40-F10. Volume: 20 Kg
The Microterrazzo Riazza collection is composed of coarse-grained microcement (<0.4mm) mixed with natural colored flakes, called Riazza. Only available with the Microdur line. Suitable for indoor and outdoor use. Classified according to UNE-EN 13813 as CT-C40-F10. Volume: 22 Kg
The Micronature collection is composed of coarse-grained microcement (<0.4 mm) mixed with recycled particles (seeds, wood, straw, etc.). A large number of effects are achieved, very different from each other, but with a common denominator: they all evoke nature. The final aesthetic result is an atmosphere of well-being, delicacy and tranquility. In perfect harmony with any style of decoration or architecture. We produce this collection with the Microdur line. Thus, it can be applied on several surfaces, from walls to floors. Suitable for indoor and outdoor use. Classified according to UNE-EN 13813 as CT-C40-F10. Volume: 22 kg
The Microterrazzo Crystal collection is composed of coarse-grained microcement (<0.4 mm) mixed with crystals and minerals called Crystal. Available in Microdur and Microrock lines. In Cemher we don't only care about the aesthetics of the coating, but also about its performance, that's why we manufacture this collection with the Microdur and Microrock lines. Thus, it can be applied on several surfaces, from walls and floors with intense traffic to swimming pools. Suitable for indoor and outdoor use. Classified according to UNE-EN 13813 as CT-C40-F10. Volume: 22Kg – Microdur I 12Kg – Microröck + Catalyst
Two-component self-leveling polymer mortar. Formulated in a white base so that it can be colored in any color and to which stones and crystals are added. High technical performance, to be applied from 8 to 12 mm thick, in the creation of continuous paving for decorative use. Warm and innovative in interiors, mainly in homes and shops, giving them an avant-garde look. Classified according to UNE-EN 13813 as CT-C40-F10. Volume: 20Kg + 20Kg
Two-component decorative metal coating for interior and exterior vertical surfaces. Made from selected metal alloy powders and water based resins. Metalresin is specially developed to be polished or oxidized. Suitable for: Vertical surfaces.
New, highly decorative, two-component and waterproof coating. It can be oxidized and polished, highlighting the beauty of the metal. The white base allows it to be pigmented, being able to create an infinity of different colors. Specially indicated for decorating walls and furniture. Also for outdoor and indoor wet areas such as showers. Consumption: 1.5Kg/m². Suitable for: Vertical and horizontal surfaces.
Oximetal is a two-component corten steel coating for indoor and outdoor vertical and horizontal surfaces. It is made of steel powders and water-based resins. Oximetal is specially developed to be oxidized, but it can also be polished. Consumption: 1.5 kg/m². Suitable for: Vertical and horizontal surfaces.
By applying Oxidher Activator on Oxymetal, Metalresin, Metalplus or Micrometal, we can create the corten steel system. Any metal surface can be oxidized in less than five minutes. Its base was specially designed to oxidize metal particles: steel, copper, gold, bronze and others. Format: 1L Suitable for: Vertical and horizontal surfaces.
Water-resistant acrylic coating that creates a glossy or matte film on concrete pavements. It is especially indicated for printed concrete pavements that require high protection against wear. Its special formula is developed to extend the life of pavements by enhancing the color of the print, providing greater scratch resistance and supporting moderate traffic. The matte finish offers the same protection, but leaving the natural look of the concrete visible. Finish: glossy Application: roller or spray Consumption: 0.25Kg/m².
It is a one-component, water-based acrylic finish for stamped concrete floors and other substrates. It spreads evenly, leaving a completely homogeneous film. Invigorates pavement colors and prevents premature evaporation of mixing water. Finish: glossy Application: roller or sprayer Consumption: 0.2Kg/m².
Floor protect is a product specially developed for the maintenance and protection of microcement. It waterproofs, invigorates and protects previously varnished surfaces. Restores light scratches on the floor. It does not contain wax, so it does not scratch with steps and does not disappear in a short period of time. Only by applying it and spreading it with a mop will we protect our floors for long periods of time. Volume: 5L Consumption: 12 m²/L
Aquamax Pro is a two-component water-based polyurethane coating with excellent hardness and chemical resistance. Developed with the innovative WMA (Without Matting Agents) technology, characterized by the absence of matting agents in satin and matte finishes. This provides excellent chemical and stain resistance. Another important feature is the choice of hardener according to the type of surface (Walls 500ml and Floors 1L). The higher the amount of hardener, the higher the hardness and chemical resistance of the coating. Suitable for the protection of surfaces with intense traffic such as sidewalks, sports fields, concrete, wood, parquet and in general those surfaces that require an excellent aesthetic and protective coating. Very high resistance to scratches and chemicals such as bleach, sulphides or vinegar. Does not absorb wine, coffee or oil stains. With 50% solids, Aquamax Pro offers higher fill for longer lasting coverage. Even on solids, it provides excellent roller application with a spray gun-like finish. Suitable for exterior and interior applications. Floor format: 5L + 1L Wall format: 5L + 500ml
Aquapur 70 Colorless water-based resin varnish, extremely hard and with excellent water resistance. It stands out for the fact that it is the only water-based polyurethane with very high hardness and high solids content, special characteristics that give it unparalleled resistance to stains; both chemical products, those produced by shoe marks and stains impregnated with dirt, which are difficult to clean with other polyurethanes. Its high content of solids, higher than other water-based polyurethanes (65% solids), ensures a very high degree of impermeability, sealing absorbent substrates with a much higher capacity, making any type of substrate more impermeable. The high percentage of hardener (40%) on comp A gives the product an exceptional hardness without shortening the life of the product mixture; more than 2 hours of validity. Volume: 5L + 2L
It is a one-component acrylic sealant with a high solids content. Waterproofs the substrate and seals it for subsequent application of polyurethane finishes. It reduces their consumption and avoids the knees through its pore-sealing action. Volume: 5L
The range of inorganic pigments. They have good resistance to ultraviolet radiation and weathering. High concentration for coloring all our water based product lines. Volume: 1L.
Highly decorative pigments, specially designed for use on microcement or concrete. They have an acrylic base and very good penetrability. They can create a wide variety of natural effects. Unlike acids on the market, whose effect is similar, Stone Effect does not require a chemical reaction. This makes it possible to control the coloring and therefore the final aesthetic result. Can be applied with a spray, sponge or brush. Consumption: 10 – 12 m²/L Volume: 1L.
They are highly additive polymers with mineral pigments. With these 40 dyes, every color in our color chart can be made. If you want to get more colors with these 40 concentrates, you can create up to 8 gradations of each dye, for a total of 328 colors. Volume: 1L.
Fine granulometry. It is characterized by its light stucco effect. Its stucco effect is much more subtle than that of the Traditional finish, whose intensity can be intensified or attenuated during application, thus showing an elegant manual profile that makes each project unique and unrepeatable.
Coarse grain size. It is distinguished by the special finish that creates a concrete effect. It has a high hardness and resistance, but due to its irregular handmade finish, it is recommended for use on walls, furniture or ceilings.
